View B43545_8873886.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

aluminum electrolytic capacitors snap-in capacitors series/type: B43545 date: november 2012 ? epcos ag 2012. reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without epcos' prior express consent is prohibited.
long-life grade capacitors applications frequency converters solar inverters uninterruptible power supplies professional power supplies medical appliances telecommunications features outstanding ripple current capability base cooling available upon request for case sizes 30 35 mm to 35 55 mm long useful life very high cv product, compact high reliability extremely improved performance at high frequencies outstanding low esr at operating conditions above 50 c optimized internal thermal resistance different case sizes available for each capacitance value capacitors with all insulation versions pass the needle flame test according to iec 60695-11-5 for all flame exposure times up to 120 s rohs-compatible construction charge/discharge-proof, polar aluminum case, fully insulated with pvc version with pet insulation available version with additional pet insulation cap on terminal side available for insulating the capacitor from the pcb snap-in solder pins to hold component in place on pc-board minus pole marking on case surface minus pole not insulated from case overload protection by safety vent on the case wall terminals standard version with 2 terminals, 2 lengths available: 6.3 and 4.5 mm 3 terminals to ensure correct insertion: length 4.5 mm snap-in capacitors B43545 outstanding ripple current, compact 105 c page 2 of 17 please read cautions and warnings and important notes at the end of this document.
1) refer to chapter "general technical information, 5 useful life" on how to interpret useful life. specifications and characteristics in brief rated voltage v r 400 ... 450 v dc surge voltage v s 1.10 v r rated capacitance c r 82 ... 820 f capacitance tolerance 20% m dissipation factor tan d (20 c, 120 hz) v r = 400 v dc: tan d 0.15 v r = 450 v dc: tan d 0.20 leakage current i leak (5 min, 20 c) self-inductance esl approx. 20 nh useful life 1) requirements: 105 c; v r ; i ac,r > 5000 h d c/c 20% of initial value 85 c; v r ; i ac,r > 20000 h tan d 2 times initial specified limit 50 c; v r ; 1.4 i ac,r > 175000 h i leak initial specified limit voltage endurance test post test requirements: 105 c; v r 2000 h d c/c 10% of initial value tan d 1.3 times initial specified limit i leak initial specified limit vibration resistance test to iec 60068-2-6, test fc: frequency range 10 hz ... 55 hz, displacement amplitude 0.35 mm, acceleration max. 5 g , duration 3 2 h. capacitor mounted by its body which is rigidly clamped to the work surface. characteristics at low temperature max. impedance ratio v r 400 v 450 v at 100 hz z -25 c / z 20 c 3 7 z -40 c / z 20 c 7 12 iec climatic category to iec 60068-1: v r = 400 v dc: 40/105/56 ( 40 c/+105 c/56 days damp heat test) v r = 450 v dc: 25/105/56 ( 25 c/+105 c/56 days damp heat test) the capacitors can be operated in the temperature range of 40 c to +105 c but the impedance at 40 c should be taken into consideration. detail specification sectional specification similar to cecc 30301-809 iec 60384-4 B43545 outstanding ripple current, compact 105 c page 3 of 17 please read cautions and warnings and important notes at the end of this document.
dimensional drawings snap-in capacitors with standard insulation (pvc or pet) snap-in terminals, length (6.3 1) mm. also available in a shorter version with a length of (4.5 1) mm. pet insulation is marked with label "pet" on the sleeve. snap-in capacitors are also available with 3 terminals (length (4.5 1) mm). pet insulation is marked with label "pet" on the sleeve. dimensions (mm) approx. weight (g) packing units (pcs.) d +1 l 2 25 25 13 130 25 30 17 130 25 35 19 130 25 40 22 130 25 45 25 130 25 50 29 130 25 55 32 130 dimensions (mm) approx. weight (g) packing units (pcs.) d +1 l 2 30 25 17 80 30 30 23 80 30 35 29 80 30 40 36 80 30 45 41 80 30 50 46 80 30 55 53 80 35 25 22 60 35 30 29 60 35 35 36 60 35 40 41 60 35 45 56 60 35 50 70 60 35 55 81 60 B43545 outstanding ripple current, compact 105 c page 4 of 17 please read cautions and warnings and important notes at the end of this document.
snap-in capacitors with pvc insulation and pet insulation cap on terminal side snap-in terminals, length (6.3 +1/ 1.4) mm. also available in a shorter version with a length of (4.5 1.4) mm. pet insulation cap is positioned under the insulation sleeve. snap-in capacitors are also available with 3 terminals (length (4.5 1.4) mm). pet insulation cap is positioned under the insulation sleeve. dimensions (mm) approx. weight (g) packing units (pcs.) d +1.4 l +2.2/ 2 25 25 13 130 25 30 17 130 25 35 19 130 25 40 22 130 25 45 25 130 25 50 29 130 25 55 32 130 dimensions (mm) approx. weight (g) packing units (pcs.) d +1.4 l +2.2/ 2 30 25 17 80 30 30 23 80 30 35 29 80 30 40 36 80 30 45 41 80 30 50 46 80 30 55 53 80 35 25 22 60 35 30 29 60 35 35 36 60 35 40 41 60 35 45 56 60 35 50 70 60 35 55 81 60 B43545 outstanding ripple current, compact 105 c page 5 of 17 please read cautions and warnings and important notes at the end of this document.
packing of snap-in capacitors for ecological reasons the packing is pure cardboard. components can be withdrawn (in full or in part) in the correct position for insertion. ordering codes for terminal styles and insulation features identification in 3rd block of ordering code snap-in capacitors terminal version insulation version pvc pet pvc plus pet cap standard terminals 6.3 mm m000 m060 m080 short terminals 4.5 mm m007 m067 m087 3 terminals 4.5 mm m002 m062 m082 ordering examples: B43545a5107m007 } snap-in capacitor with short terminals and standard pvc insulation B43545a5107m062 } snap-in capacitor with 3 terminals and pet insulation B43545a5107m080 } snap-in capacitor with standard terminals and pvc insulation with additional pet insulation cap on terminal side B43545 outstanding ripple current, compact 105 c page 6 of 17 please read cautions and warnings and important notes at the end of this document.
overview of available types v r (v dc) 400 450 case dimensions d l (mm) c r ( m f) 82 25 25 100 25 30 120 25 25 25 35 30 25 150 25 30 25 40 30 30 180 25 35 30 25 25 45 30 35 35 25 220 25 35 30 30 25 50 30 35 35 30 270 25 45 30 35 35 25 30 45 35 35 330 25 50 30 35 35 30 30 50 35 40 390 25 55 30 40 35 35 30 55 35 45 470 30 50 35 40 35 50 560 30 55 35 40 35 55 680 35 50 820 35 55 the capacitance and voltage ratings listed above are available in different cases upon request. other voltage and capacitance ratings are also available upon request. B43545 outstanding ripple current, compact 105 c page 7 of 17 please read cautions and warnings and important notes at the end of this document.
1) 120-hz conversion factor of ripple current: i ac (120 hz) = 1.03 i ac (100 hz) technical data and ordering codes c r 100 hz 20 c m f case dimensions d l mm esr typ 100 hz 20 c m w esr typ 300 hz 60 c m w z max 10 khz 20 c m w i ac,max 100 hz 60 c a i ac,max 100 hz 85 c a i ac,r 1) 100 hz 105 c a ordering code (composition see below) composition of ordering code * = insulation feature # = terminal style 0 = pvc insulation 6 = pet insulation 8 = pvc insulation with additional pet insulation cap on terminal side 0 = snap-in standard terminals (6.3 mm) 2 = snap-in 3 terminals (4.5 mm) 7 = snap-in short terminals (4.5 mm) v r = 400 v dc 120 25 25 500 160 700 2.23 1.64 0.88 B43545a9127m0*# 150 25 30 400 130 550 2.60 1.92 1.04 B43545a9157m0*# 180 25 35 330 110 460 2.96 2.19 1.18 B43545a9187m0*# 180 30 25 330 100 460 3.12 2.31 1.24 B43545b9187m0*# 220 25 35 270 90 380 3.36 2.48 1.33 B43545a9227m0*# 220 30 30 270 85 370 3.58 2.64 1.42 B43545b9227m0*# 270 25 45 220 70 310 3.96 2.93 1.58 B43545a9277m0*# 270 30 35 220 70 300 4.12 3.04 1.64 B43545b9277m0*# 270 35 25 220 75 310 4.15 3.06 1.65 B43545c9277m0*# 330 25 50 180 60 260 4.58 3.39 1.82 B43545a9337m0*# 330 30 35 180 55 250 4.69 3.46 1.86 B43545b9337m0*# 330 35 30 180 60 260 4.79 3.54 2.03 B43545c9337m0*# 390 25 55 160 50 220 5.19 3.84 2.07 B43545a9397m0*# 390 30 40 150 50 210 5.30 3.91 2.24 B43545b9397m0*# 390 35 35 150 50 220 5.38 3.98 2.28 B43545c9397m0*# 470 30 50 130 40 180 6.11 4.51 2.59 B43545a9477m0*# 470 35 40 130 40 180 6.11 4.52 2.59 B43545b9477m0*# 560 30 55 110 34 150 6.95 5.13 2.94 B43545a9567m0*# 560 35 40 110 36 160 6.80 5.02 2.87 B43545b9567m0*# 680 35 50 90 30 130 7.87 5.82 3.33 B43545a9687m0*# 820 35 55 75 26 110 8.99 6.64 3.80 B43545a9827m0*# v r = 450 v dc 82 25 25 1110 290 1680 1.80 1.32 0.71 B43545a5826m0*# 100 25 30 910 240 1370 2.06 1.52 0.82 B43545a5107m0*# 120 25 35 760 200 1140 2.34 1.73 0.94 B43545b5127m0*# 120 30 25 750 190 1140 2.47 1.81 0.98 B43545a5127m0*# 150 25 40 610 160 920 2.74 2.02 1.09 B43545a5157m0*# 150 30 30 600 150 910 2.86 2.10 1.14 B43545b5157m0*# 180 25 45 500 130 770 3.13 2.30 1.25 B43545a5187m0*# B43545 outstanding ripple current, compact 105 c page 8 of 17 please read cautions and warnings and important notes at the end of this document.
2) 120-hz conversion factor of ripple current: i ac (120 hz) = 1.03 i ac (100 hz) technical data and ordering codes c r 100 hz 20 c m f case dimensions d l mm esr typ 100 hz 20 c m w esr typ 300 hz 60 c m w z max 10 khz 20 c m w i ac,max 100 hz 60 c a i ac,max 100 hz 85 c a i ac,r 2) 100 hz 105 c a ordering code (composition see below) composition of ordering code * = insulation feature # = terminal style 0 = pvc insulation 6 = pet insulation 8 = pvc insulation with additional pet insulation cap on terminal side 0 = snap-in standard terminals (6.3 mm) 2 = snap-in 3 terminals (4.5 mm) 7 = snap-in short terminals (4.5 mm) v r = 450 v dc 180 30 35 500 130 760 3.24 2.38 1.29 B43545b5187m0*# 180 35 25 510 130 770 3.32 2.44 1.32 B43545c5187m0*# 220 25 50 410 110 630 3.63 2.67 1.45 B43545a5227m0*# 220 30 35 410 110 630 3.70 2.72 1.47 B43545b5227m0*# 220 35 30 410 110 630 3.82 2.81 1.62 B43545c5227m0*# 270 30 45 330 85 510 4.31 3.17 1.83 B43545a5277m0*# 270 35 35 340 90 510 4.37 3.22 1.85 B43545b5277m0*# 330 30 50 270 70 420 4.98 3.66 2.11 B43545a5337m0*# 330 35 40 280 70 420 5.02 3.69 2.13 B43545b5337m0*# 390 30 55 230 60 350 5.64 4.15 2.39 B43545a5397m0*# 390 35 45 230 60 360 5.63 4.14 2.39 B43545b5397m0*# 470 35 50 190 50 300 6.41 4.72 2.72 B43545a5477m0*# 560 35 55 160 45 250 7.28 5.35 3.08 B43545a5567m0*# B43545 outstanding ripple current, compact 105 c page 9 of 17 please read cautions and warnings and important notes at the end of this document.
1) refer to chapter "general technical information, 5 useful life" on how to interpret useful life. useful life 1) the useful life graph is calculated for each individual capacitor and is available upon request. frequency factor of permissible ripple current i ac versus frequency f typical behavior frequency characteristics of esr typical behavior B43545 outstanding ripple current, compact 105 c page 10 of 17 please read cautions and warnings and important notes at the end of this document.
impedance z versus frequency f typical behavior at 20 c B43545 outstanding ripple current, compact 105 c page 11 of 17 please read cautions and warnings and important notes at the end of this document.
cautions and warnings personal safety the electrolytes used by epcos have been optimized both with a view to the intended application and with regard to health and environmental compatibility. they do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (dmf) or dimethyl acetamide (dmac). furthermore, some of the high-voltage electrolytes used by epcos are self-extinguishing. as far as possible, epcos does not use any dangerous chemicals or compounds to produce operating electrolytes. however, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no alternative materials are currently known. however, the amount of dangerous materials used in our products is limited to an absolute minimum. materials and chemicals used in epcos aluminum electrolytic capacitors are continuously adapted in compliance with the epcos corporate environmental policy and the latest eu regulations and guidelines such as rohs, reach/svhc, gadsl, and elv. mds (material data sheets) are available on the epcos website for all types listed in the data book. mds for customer specific capacitors are available upon request. msds (material safety data sheets) are available for all of our electrolytes upon request. nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors: no electrolyte should come into contact with eyes or skin. if electrolyte does come into contact with the skin, wash the affected areas immediately with running water. if the eyes are affected, rinse them for 10 minutes with plenty of water. if symptoms persist, seek medical treatment. avoid inhaling electrolyte vapor or mists. workplaces and other affected areas should be well ventilated. clothing that has been contaminated by electrolyte must be changed and rinsed in water. B43545 outstanding ripple current, compact 105 c page 12 of 17 please read cautions and warnings and important notes at the end of this document.
product safety the table below summarizes the safety instructions that must be observed without fail. a detailed description can be found in the relevant sections of chapter "general technical information". topic safety information reference chapter "general technical information" polarity make sure that polar capacitors are connected with the right polarity. 1 "basic construction of aluminum electrolytic capacitors" reverse voltage voltages polarity classes should be prevented by connecting a diode. 3.1.6 "reverse voltage" mounting position of screw- terminal capacitors do not mount the capacitor with the terminals (safety vent) upside down. 11.1. "mounting positions of capacitors with screw terminals" robustness of terminals the following maximum tightening torques must not be exceeded when connecting screw terminals: m5: 2.5 nm m6: 4.0 nm 11.3 "mounting torques" mounting of single-ended capacitors the internal structure of single-ended capacitors might be damaged if excessive force is applied to the lead wires. avoid any compressive, tensile or flexural stress. do not move the capacitor after soldering to pc board. do not pick up the pc board by the soldered capacitor. do not insert the capacitor on the pc board with a hole space different to the lead space specified. 11.4 "mounting considerations for single-ended capacitors" soldering do not exceed the specified time or temperature limits during soldering. 11.5 "soldering" soldering, cleaning agents do not allow halogenated hydrocarbons to come into contact with aluminum electrolytic capacitors. 11.6 "cleaning agents" upper category temperature do not exceed the upper category temperature. 7.2 "maximum permissible operating temperature" passive flammability avoid external energy, such as fire or electricity. 8.1 "passive flammability" B43545 outstanding ripple current, compact 105 c page 13 of 17 please read cautions and warnings and important notes at the end of this document.
topic safety information reference chapter "general technical information" active flammability avoid overload of the capacitors. 8.2 "active flammability" maintenance make periodic inspections of the capacitors. before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. do not apply any mechanical stress to the capacitor terminals. 10 "maintenance" storage do not store capacitors at high temperatures or high humidity. capacitors should be stored at +5 to +35 c and a relative humidity of 75%. 7.3 storage conditions reference chapter "capacitors with screw terminals" breakdown strength of insulating sleeves do not damage the insulating sleeve, especially when ring clips are used for mounting. "screw terminals accessories" B43545 outstanding ripple current, compact 105 c page 14 of 17 please read cautions and warnings and important notes at the end of this document.
symbols and terms symbol english german c capacitance kapazit?t c r rated capacitance nennkapazit?t c s series capacitance serienkapazit?t c s,t series capacitance at temperature t serienkapazit?t bei temperatur t c f capacitance at frequency f kapazit?t bei frequenz f d case diameter, nominal dimension geh?usedurchmesser, nennma? d max maximum case diameter maximaler geh?usedurchmesser esl self-inductance eigeninduktivit?t esr equivalent series resistance ersatzserienwiderstand esr f equivalent series resistance at frequency f ersatzserienwiderstand bei frequenz f esr t equivalent series resistance at temperature t ersatzserienwiderstand bei temperatur t f frequency frequenz i current strom i ac alternating current (ripple current) wechselstrom i ac,rms root-mean-square value of alternating current wechselstrom, effektivwert i ac,f ripple current at frequency f wechselstrom bei frequenz f i ac,max maximum permissible ripple current maximal zul?ssiger wechselstrom i ac,r rated ripple current nennwechselstrom i ac,r (b) rated ripple current for base cooling nennwechselstromstrom fr bodenkhlung i leak leakage current reststrom i leak,op operating leakage current betriebsreststrom l case length, nominal dimension geh?usel?nge, nennma? l max maximum case length (without terminals and mounting stud) maximale geh?usel?nge (ohne anschlsse und gewindebolzen) r resistance widerstand r ins insulation resistance isolationswiderstand r symm balancing resistance symmetrierwiderstand t temperature temperatur d t temperature difference temperaturdifferenz t a ambient temperature umgebungstemperatur t c case temperature geh?usetemperatur t b capacitor base temperature temperatur des becherbodens t time zeit d t period zeitraum t b service life (operating hours) brauchbarkeitsdauer (betriebszeit) B43545 outstanding ripple current, compact 105 c page 15 of 17 please read cautions and warnings and important notes at the end of this document.
symbol english german v voltage spannung v f forming voltage formierspannung v op operating voltage betriebsspannung v r rated voltage, dc voltage nennspannung, gleichspannung v s surge voltage spitzenspannung x c capacitive reactance kapazitiver blindwiderstand x l inductive reactance induktiver blindwiderstand z impedance scheinwiderstand z t impedance at temperature t scheinwiderstand bei temperatur t tan d dissipation factor verlustfaktor l failure rate ausfallrate e 0 absolute permittivity elektrische feldkonstante e r relative permittivity dielektrizit?tszahl w angular velocity; 2 p f kreisfrequenz; 2 p f note all dimensions are given in mm. B43545 outstanding ripple current, compact 105 c page 16 of 17 please read cautions and warnings and important notes at the end of this document.
the following applies to all products named in this publication: 1. some parts of this publication contain statements about the suitability of our products for certain areas of application . these statements are based on our knowledge of typical re- quirements that are often placed on our products in the areas of application concerned. we nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application . as a rule, epcos is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. for these reasons, it is always ultimately incum- bent on the customer to check and decide whether an epcos product with the properties de- scribed in the product specification is suitable for use in a particular customer application. 2. we also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified . in customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. the warnings, cautions and product-specific notes must be observed. 4. in order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . useful information on this will be found in our ma- terial data sheets on the internet (www.epcos.com/material). should you have any more de- tailed questions, please contact our sales offices. 5. we constantly strive to improve our products. consequently, the products described in this publication may change from time to time . the same is true of the corresponding product specifications. please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. we also reserve the right to discontinue production and delivery of products . consequently, we cannot guarantee that all products named in this publication will always be available. the aforementioned does not apply in the case of individual agreements deviating from the fore- going for customer-specific products. 6. unless otherwise agreed in individual contracts, all orders are subject to the current ver- sion of the "general terms of delivery for products and services in the electrical in- dustry" published by the german electrical and electronics industry association (zvei) . 7. the trade names epcos, baoke, alu-x, ceradiode, ceralink, csmp, cssp, ctvs, deltacap, digisimic, dssp, filtercap, formfit, miniblue, minicell, mkd, mkk, mlsc, motorcap, pcc, phasecap, phasecube, phasemod, phicap, siferrit, sifi, sikorel, silvercap, simdad, simic, simid, sineformer, siov, sip5d, sip5k, thermofuse, windcap are trademarks registered or pending in europe and in other countries. further information will be found on the internet at www.epcos.com/trademarks. important notes page 17 of 17

▲Up To Search▲

Price & Availability of B43545

	To Download B43545 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .